Better Braking Starts Before the First Ride
Introducing the TRP x Sinter Smart Bedding Machine
More braking performance. Less time in the workshop. Consistent results from the first pull of the lever.
A new bike rolling off the showroom floor should be ready to perform. The same goes for a fresh set of brake pads leaving the service department. But there's one critical step that can make a significant difference in braking performance: properly bedding in the brakes.
That's where the TRP x Sinter Smart Bedding Machine comes in.
Developed by Sinter and available through TRP, the Smart Bedding Machine takes the guesswork out of one of the most important steps in brake preparation. By automating wheel rotation and guiding mechanics through a controlled bedding process, it delivers consistent results while saving valuable workshop time.
A New Bike Should Be Ready to Ride
Think about buying a new car. When you drive it off the lot, you expect it to be ready to perform. You don't expect the dealership to hand you the keys and tell you the brakes aren't fully prepared.
So why should buying a new bike be any different?
It's not uncommon for bike shops to send customers home with new bikes or freshly installed brake pads and advise them to take it easy until the brakes are properly bedded in. In many cases, the responsibility of completing this critical process falls on the customer.
But proper brake bedding requires a specific procedure, and not every rider understands how to perform it correctly. Inconsistent or incomplete bedding can result in reduced braking performance, unpredictable brake feel, and a potentially frustrating first ride.
Beyond the customer experience, this approach raises important safety considerations and can expose shops to unnecessary liability concerns.
The Smart Bedding Machine offers a better approach. By bringing a controlled, repeatable bedding process into the workshop, shops can take ownership of brake preparation and deliver bikes with properly bedded brakes before they leave the service department.
It's a simple shift in the process that helps improve safety, builds customer confidence, and reinforces the value of professional bicycle service.
Why Proper Brake Bedding Matters
Installing new brake pads is only part of the job.
Before a braking system can deliver its intended performance, the pads and rotors need to be properly bedded in. This process establishes a consistent layer of friction material on the rotor surface through repeated, controlled braking cycles.
When done correctly, bedding helps improve initial bite, braking consistency, and overall feel at the lever.
Traditionally, mechanics perform this process by riding a bike through a series of accelerations and controlled stops. While effective when performed correctly, the results can vary depending on the mechanic, available space, weather conditions, and the braking system itself.
For busy bike shops, it's also another task that takes technicians away from the workbench.
Over 20% More Braking Performance
Performance isn't just about the components you install. It's also about how you prepare them.
According to Sinter's testing, brake pads prepared using the Smart Bedding Machine demonstrated more than 20% greater braking performance compared to pads bedded using traditional parking lot methods.
The difference comes from consistency.
Rather than relying on a mechanic to estimate braking force, speed, and cooling intervals, the machine uses a guided program to help control the bedding process.
The result is a more consistent preparation procedure designed to deliver strong initial braking performance before the bike ever hits the trail.
For riders, that means greater confidence in their braking system from the first ride. For shops, it means a repeatable process that can be incorporated into routine service and new bike assembly.
Less Time Bedding. More Time Wrenching.
Time is one of the most valuable resources in any service department.
Whether you're assembling a new bike, replacing worn brake pads, or preparing a customer's bike for the weekend, every additional step affects workshop efficiency.
The Smart Bedding Machine allows technicians to complete the bedding process in just a few minutes, without taking the bike outside for repeated braking runs.
Rain, snow, or summer heat? No problem. The process takes place right in the workshop.
By reducing the time spent bedding brakes, shops can free up technicians for other service tasks, improve workflow, and potentially increase the number of bikes moving through the service department.
It's a simple improvement that can make a meaningful difference in a busy workshop.
Smart Technology. Simple Operation.
The TRP x Sinter Smart Bedding Machine is designed to make professional brake preparation straightforward. Its dual-drive V-form aluminum rollers accommodate wheel sizes from 20 to 32 inches and tire widths from 1.0 to 3.0 inches, making it suitable for a wide variety of bikes. An intuitive control panel guides technicians through the process, with selectable programs based on rotor size and braking system.
During operation, the machine provides feedback on braking force and timing, helping the technician apply consistent pressure and follow the appropriate braking and cooling cycles. A touchless foot sensor allows the operator to change wheel direction when switching between front and rear brakes, keeping the process simple and efficient.
Key Features
- Guided bedding programs for consistent results
- Dual-drive aluminum rollers for secure wheel engagement
- Compatibility with 20–32-inch wheels
- Accommodates tire widths from 1.0–3.0 inches
- Touchless foot sensor for changing wheel direction
- Integrated braking force and timing feedback
- Indoor operation independent of weather conditions
Take the Guesswork Out of Brake Bedding
Great braking performance starts with great components, but proper preparation is just as important.
The TRP x Sinter Smart Bedding Machine brings precision, consistency, and efficiency to a process that's traditionally been performed by feel. For shops looking to streamline service operations and deliver a better experience to customers, it's an investment in both workshop efficiency and braking performance.
Better bedding. Better braking. From the very first ride.
